![]() ![]() The article went into extreme detail in the method of sealing the cartridge to prevent gas escaping and thus make it quieter: What round did it fire? Well, like the Nagant before it, the cartridge was very special. The gun made its first mention in the “gun rags” in the September 1992 issue of Soldier of Fortune magazine. Then the whole affair was coated black, a bipod was fitted, and the result was a 36.5-inch long, 8.5-pound integrally suppressed revolver. Over the barrel, a 6061 T6 aluminum suppressor tube 18.5-inches long was fitted. 30 caliber 1-in-9-inch right-hand twist example that had a gap between the cylinder and the barrel of 0.005 inch. 44 Magnum and replaced the barrel with a 10-inch. Their answer was a unique weapon based upon a Ruger Super Red Hawk.Īccording to reports, Knight took a commercial Redhawk. Reed Knight Jr.’s Knight’s Armament Co (KAC) of Vero Beach, Florida responded to a call from a government agency yet unnamed to produce a small and short-ranged suppressed rifle. Just 75 were made and, though quickly withdrawn from Army use, were purportedly still utilized by SOG in places that never existed late into the war.īack in the early 1990s, C. Since the ammunition itself had about as much powder as a Fourth of July party popper, the gun was fitted with a short smoothbore barrel and did not need a suppressor. 410-ish Quiet Special Purpose Round filled with 15 tungsten balls in a plastic sabot. 44 Magnum that was chambered for a very low power special. Note S&W Smith Wesson suppressed revolver (Photo: Australian War Memorial)Īnother attempted solution was the 1969-era Quiet Special Purpose Revolver, a converted Smith & Wesson Model 29. ![]() Moscow liked the concept so much they even used a version of the Brambit for their full-sized M91 rifles but that is a whole ‘nother story.Īs a proof of concept, Utah-based SilencerCo has often trotted out a suppressed Nagant to trade shows over the years and has talked about the unique characteristics of the neat-o Russki wheel gun.Īustralian combat engineer assisting American forces in Vietnam with tunnel clearing operations Vietnam, Phuoc Tuy Province, 1966. The Soviets later figured this out and created what was known as the Brambit Device to convert an ordinary M1895 to a suppressed revolver. Nagant engineered his creation this way to produce a mild boost in velocity for the otherwise anemic cartridge, it also had the unintentional side benefit of allowing these fairly common military classics to be suppressed - provided you can mate a suppressor to the barrel after threading it or using a coupler. ![]() All this comes together to create a wonky action that cams the cylinder and barrel almost shut, thus nearly eliminating the gap that almost every other revolver has. Further, each chamber of the revolver is countersunk to mate with the barrel while the special 7.62x38Rmm ammunition used has a very deep-set bullet design. On the M1895, when the trigger is pulled the cylinder is not only rotated but also moved forward, so it comes very close to the forcing cone. One such revolver is Emile Nagant’s series of gas-seal revolvers such as the Russian M1895. With the problem in suppressing a revolver resting in the barrel-cylinder gap, finding a creative way to plug that gap can make a wheel gun a more effective suppressor platform. ![]() Now that the rule is explained, there are, as with any rule, a few exceptions. This, of course, has not stopped Hollywood from extensively showing such fictional contraptions to be “ twhip-twhip” silent in movies like The Sting and Desperado. Lee Marvin famously carried a whole series of suppressed roscoes in the 1964 film, The Killers, a crime flick that also featured future President Ronald Regan. So, while you can thread the barrel of a revolver and attach a suppressor to it, the barrel-cylinder gap is still going to allow gas, and thus noise, to escape. This is because, in general, while a suppressor can help reduce (but not eliminate) the report of a gunshot by slowly dissipating the escaping gasses caught in the suppressor tube at the muzzle, the gap between a revolver’s cylinder and barrel’s forcing cone allows some gas to escape at the other end, thus defeating the purpose. Left out of the equation at the time were wheel guns as the humble revolver did not lend itself well to having its sound signature moderated. The original Maxim Silencer Company, as far back as the 1910s, advertised and sold numerous types of suppressors along with a series of barrel couplings to accommodate a range of rifles and pistols. The question of whether you can put a suppressor or silencer on a revolver is a loaded one that has a simple answer as well as a few exceptions to the rule. Can you slap a suppressor on a revolver and make it work? That’s a trick question. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |